Home > HARDWARE > CONSTRUCTION HARDWARE > JOIST HANGERS & CONNECTORS
Choose a sub category:
JOIST HANGERS FRAMING ANGLES/ANCHORS MENDING PLATES
NAIL PLATES POST ANCHORS / CAPS FENCE BRACKETS
BRIDGING INSULATION SUPPORTS STRAPS
PLYWOOD CLIPS FOUNDATION ANCHORS BRICK/WALL TIES
MISC CONSTR HARDWARE
Sort By:
1 2 3 ... 6
USP Lumber JL26IF-TZ Standard Invert Flange Joist Hanger USP Lumber PCP Post Cap USP Lumber JL28IF-TZ Standard Invert Flange Joist Hanger
Speed prongs designed to temporarily position hangers on headers for more convenient nail fastening. G-185 galvanizing finish. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes. These seamless caps keep water off post tops, protecting wood from moisture damage. The PCP's plastic construction is corrosion-proof and paintable. Speed prongs designed to temporarily position hangers on headers for more convenient nail fastening. G-185 galvanizing finish. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes.
USP Lumber RT16ATZ Double Plate Hurricane/Seismic Anchor USP Lumber JUS210-2TZ Double Shear Slant Joint Hanger Squeek No More 1011345 Screw Set
These anchors tie trusses and rafters to top plates and may be used to tie wood framing members to resist uplift and lateral forces. The JUS hanger Series offers double shear nailing. USP's dimple allows for 30 deg to 45 deg nailing through the joist into the header resulting in higher loads and less nailing. Slant/double shear nailing allows for higher load values, fewer nails and faster installation. Specially scored waxed screws. Scored head breaks off at the same place every time. Carded.
Acorn IHW16100 Insulation Support Wire 16 in L USP Lumber HPAHD22 Foundation Strap Squeek No More 1010543 Floor Squeak Repair Kit
Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2 in less than over center joist spacing. 13 ga. Designed to anchor wood framing to poured concrete, foundation straps tie mudsill and stud simultaneously to the foundation. Single pour edge installation. G90 galvanized finish. Embedment 10 in. Requires 16d nails for installation. Meets ICC-ES ESR-2787 codes. 10 ge - 24-3/4 in H1 x 10 in H2. The Squeek No More kit is designed to stop floor squeaks from above the floor by going safely through the carpet. The kit works on all carpets even berber. The Squeek No More kit has 50 screws that are scored one inch from the head and coated with a special wax that allows the screw to safely pass through the carpet. The tooling, a tripod fixture and driver bit, drives the screw safely through the carpet stopping the score on the screw slightly below the wood of the floor. Then with the tripod fixture you snap the head of the screw off. The screw thread then holds the floor to the joist without having any part of the screw sticking up that you could walk on. The kit also includes 2 joist finding tools. You use these to quickly and accurately find the joist from above the floor.
USP Lumber NA9-5MC Joist Hanger Nail Acorn IHW24100 Insulation Support Wire 24 in L USP Lumber NA11-5MC Joist Hanger Nail
Proper fasteners are a critical component in a sound wood frame structure. To ensure successful installations of its connectors, USP offers a full range of structurally-rated nails. All galvanized nails supplied by USP are hot dipped for greater corrosion resistance. Any USP connector requiring a NA16D-RS or NA20D nail is shipped with the nails attached to the connector in convenient poly bags. Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2 in less than over center joist spacing. 13 ga. Proper fasteners are a critical component in a sound wood frame structure. To ensure successful installations of its connectors, USP offers a full range of structurally-rated nails. All galvanized nails supplied by USP are hot dipped for greater corrosion resistance. Any USP connector requiring a NA16D-RS or NA20D nail is shipped with the nails attached to the connector in convenient poly bags.
RH Tamlyn PCS716 Plywood Clip USP Lumber PAU44-TZ Post Anchor RH Tamlyn PCS1532 Plywood Clip
TAMLYN PCS Framing Plywood Clip, Steel, Galvanized, Material Thickness: 20 ga, Maximum Roof Span: 24 in, Number of PC per Spans: 1 Post anchors are used to secure wood posts to concrete footings. These post anchors also provide moisture damage protection and feature a 1 in stand-off plate to elevate wood posts above concrete surfaces as required by building code. TAMLYN Framing Plywood Clip, Steel, Galvanized, Material Thickness: 20 ga, Maximum Roof Span: 32, Number of PC per Spans: 1
RH Tamlyn PCS12 Plywood Clip RH Tamlyn PCS58 Plywood Clip Deckmate 90166 Deck Bench Bracket with Bench Bracket
Replace wood blocking on roof sheathing. Tight fit for positive installation. Embossed dimples provide 1/8 in gap needed to prevent panels from popping up as sheathing expands. G60 galvanizing finish. 20 ga, Boxed. Replace wood blocking on roof sheathing. Tight fit for positive installation. Embossed dimples provide 1/8 in gap needed to prevent panels from popping up as sheathing expands. G60 galvanizing finish. 20 ga, Boxed. You determine the size. Connect with railing brackets with 2x4 and 2x6 lumber to easily add a bench to any size or shape deck. Gain increased seating area while using only 7 in of deck space. Assembled unit stands 36 in H for deck railing, seat is 17 in H. Quick and easy to assemble using basic tools. Includes bench bracket, hardware and instructions. Lumber not included.
RH Tamlyn PC1532 Plywood Clip USP Lumber PAU66-TZ Post Anchor Hopkins 90128 Shelf Link 4 ft L x 2 ft W
With built-in spacer for use when support spacing exceeds the maximum length of an unsupported edge. Boxed. Post anchors are used to secure wood posts to concrete footings. These post anchors also provide moisture damage protection and feature a 1 in stand-off plate to elevate wood posts above concrete surfaces as required by building code. You can determine the size and configuration, just add 2x4's to the ShelfLinks to make functional and custom shelving in any length, height and configuration. Made of structural resin. Can support spans up to 8 ft. Includes ShelfLinks, hardware and instructions. Lumber not included.
ANGLE 2X4IN TRIPLE ZINC 12GA  Acorn IHW16500 Insulation Support Wire 16 in L USP Lumber RS20-R Coiled Strap
ML angles are multi-purpose angles that install easily with USP's WS15 wood screws. The staggered fastener pattern allows for back-to-back installations. Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2 in less than over center joist spacing. 13 ga. Coiled strapping enables cut-to-length convenience for a variety of immediate job site needs.
Simpson Strong-Tie LSTA Light Duty Strap Tie USP Lumber RT7A Double Plate Hurricane/Seismic Anchor USP Lumber JL24 Standard Joist Hanger
Connects wood framing to resist tension forces. G90 galvanizing finish. LSTA light-duty series require 10d nails for installation. Designed for use with 1-1/2 in W framing members, including I-Joist flanges. Meets ICC-ES ESR-1781 codes. These anchors tie trusses and rafters to top plates and may be used to tie wood framing members to resist uplift and lateral forces. G90 galvanizing finish.
USP Lumber LSTA12 Light Capacity Strap Tie Deckmaster DMP125-10 Hidden Deck Bracket Kit Deckmaster DMP100-10 Hidden Deck Bracket Kit
Connects wood framing to resist tension forces. G90 galvanizing finish. LSTA light-duty series require 10d nails for installation. Designed for use with 1-1/2 in W framing members, including I-Joist flanges. Meets ICC-ES ESR-1781 codes. When using the Grabber Deckmaster fastening system, all fasteners are hidden beneath the deckboards. There is no surface penetration of the deckboards or joists. With Grabber Deckmaster there are no exposed screws a primary entry point for moisture and deck board damage. No stains or splinters form around fastener holes. When using the Grabber Deckmaster fastening system, all fasteners are hidden beneath the deckboards. There is no surface penetration of the deckboards or joists. With Grabber Deckmaster there are no exposed screws a primary entry point for moisture and deck board damage. No stains or splinters form around fastener holes.
   
 
1 2 3 ... 6